Multi function trigger delay cycle timing MOS tube control replacement relay module 5v12v2v For arduino

Xy-wm01 multi function trigger delay cycle timing MOS tube control replacement relay module 5v12v2v

Timing range: 0.01 seconds ~ 9999 minutes

This product LCD display, very clear, easy to use, powerful, but please look at the detailed buyer of this product operating instructions, very practical products.

Product highlights:

1. With LCD display, the current mode and parameters are clear, very clear, simple and practical;

2. Support key trigger control, high and low level trigger, switch control, support NPN, PNP sensor access, suitable for most occasions;

3. Wide voltage power supply (6 ~ 30V), easy to use;

4. Support UART data upload and parameter setting;

5. One key pause function, with reverse connection protection, reverse connection does not burn;

6. Sleep mode is added. After enabling, the LCD backlight will be automatically turned off without any operation for about 5 minutes, and any key will wake up;

7. Different OP, Cl and Lop parameters can be set, which are independent of each other and saved separately;

8. All setting parameters are saved automatically after power failure.

Note: MOS is live output, and the output voltage is equal to the supply voltage.

Working mode:

P0: after the signal is triggered, the MOS tube is turned on for op time, and then disconnected; within the op time, the signal is triggered again and invalid

P1: after the signal is triggered, the MOS tube is turned on for op time, and then disconnected; within the op time, the signal is triggered again and timed again

P2: after the signal is triggered, the MOS tube is turned on for op time, and then disconnected; within the op time, the signal triggers reset again, the MOS tube is disconnected, and the timing stops

P3: after the signal is triggered, the MOS switches off for CL time, and then the MOS switches on;

P4: give trigger signal, MOS turn on OP time, MOS turn off CL time, and then cycle the above action, give signal again in the cycle, restore the initial state, stop timing; the number of cycles (LOP) can be set; at the end of the cycle, keep MOS turn off;

P5: to give the trigger signal, MOS turn on OP time after the MOS turn off CL time, and then cycle the above action, give the signal again in the cycle, restore the initial state, stop timing; the number of cycles (LOP) can be set; at the end of the cycle, keep the MOS turn on;

P6: there is no need to trigger signal after power on, MOS on OP time, MOS off CL time, cycle the above actions; the number of cycles (LOP) can be set; at the end of the cycle, keep MOS off;

P7: there is no need to trigger signal after power on, MOS tube off CL time, MOS tube on OP time, cycle the above actions; the number of cycles (LOP) can be set; at the end of the cycle, keep MOS tube on;

P8: signal holding function: if there is a trigger signal, the timing will clear, and the MOS tube will remain on; when the signal disappears, the timing OP will disconnect the MOS tube; during the timing, there will be another signal, and the timing will clear;

P9: signal holding function: if there is a trigger signal, the timing will clear, and the MOS tube will remain disconnected; when the signal disappears, the MOS tube will be turned on after timing CL; during the timing, there is another signal, and the timing will clear;

(P0 ~ P7) mode, press the pause button briefly, and the system will start timing when the system has not triggered timing; when the system has timed, the system will pause timing, MOS will be disconnected, and “out” will flash to remind;

In P8 P9 mode, the key is suspended as the trigger signal in the operation interface, and the short / long press of the key function is invalid;

Product parameters:

1: Working voltage: 6-30v power supply

2: Trigger signal source: high level trigger (3.0V ~ 24V), low level trigger (0.0v ~ 0.2V), switching value control (passive switch).

3: Output capacity: it can control the equipment within 30V and 10A DC

4: Quiescent current: 15mA, working current: 50mA

5: Service life: MOS tube live output, switch unlimited times; working temperature: – 40-85 ℃; weight: 45g, size: 7.1 * 3.9 * 2.5cm (length, width and height)

6: With optocoupler isolation, enhance the anti-interference ability, industrial level circuit board, set parameters, always remember after power failure.

Timing range

0.01 seconds (minimum) ~ 9999 minutes (maximum) continuously adjustable

How to select timing range:

In the op / CL parameter modification interface, press the pause button to select the timing range;

There is no decimal point for XXX, and the timing range is from 1 second to 9999 seconds

30. X decimal point in 10, timing range 0.1 seconds ~ 999.9 seconds

XX.XX  The decimal point is 100, and the timing range is 0.01 seconds to 99.99 seconds

10. All x.x.x decimal points are on, and the timing range is from 1 minute to 9999 minutes

For example, if you want to set op to 3.2 seconds, move the decimal point to 10, and the LCD will display 003.2

Parameter Description: op on time, CL off time, number of Lop cycles (1-9999, “—” represents infinite cycles)

1, Parameter setting

a) Press and hold the setting button to enter the setting interface;

b) First, the working mode is set, the working mode flashes to remind, and the working mode is set by short pressing the increase / decrease button;

c) Short press the setting button to select the working mode and enter the system parameter setting;

d) In the system parameter setting interface, short press the setting key to switch the system parameters to be modified, and short press / long press the increase / decrease key to modify;

(Note: in the mode of P0 ~ P3 / P8 / P9, short press of the setting button is invalid);

e) In the op / CL parameter modification interface, briefly press the pause button to switch the timing unit (1s / 0.1s/0.01s/1min);

f) After all the parameters are set, long press the set button to save the parameters and exit the setting interface;